INTERNATIONAL ISO STANDARD 9692-1 Second edition 2013-09-01 Weldingand alliedprocesses-Types ofjointpreparation- Part 1: Manualmetalarcwelding gas- shieldedmetalarcwelding gas weldingTIGwelding andbeam iTehST weldingofsteels YE (standards.iteh.ai) Soudage et techniques connexes Types de preparation de joints Partigenlrvltrodenrobeoug tldageriGetsouduge par faisceau des aciers ISO 9692-1:2013(E) Reference number ISO 2013
ISO 9692-1:2013(E) iTehSTANDARDPREVIEW (standards.iteh.ai) ISO 9692-12013 htps/standards.ichai/cataogstandards/st/c022fa0-641d4c3a8295- 8961 f63de9e8/so-9692-12013 COPYRIGHTPROTECTEDDOCUMENT @ ISO 2013 All rightsreserved Unless otherwise specified no part of this publication may be reproduced or utilized otherwise in any form or by any means electronic or mechanical including photocopying or posting on the internet or an intranet without prior written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel. 41 22 749 01 11 E-mail copyright@iso.org Fax 41 22 749 09 47 Web .iso.org Published in Switzerland ii @ ISO 2013 All rights reserved
ISO 9692-1:2013(E) Contents Page Foreword. iv Introduction. 1 Scope. 1 2 Normative references. 1 3 Materials. 1 4 Welding processes. 5 Finish. 2 6 Type of joint preparation 2 Bibliography. 14 iTehSTANDARDPREVIEW (standards.iteh.ai) ISO 9692-12013 htps:/standards.itchaicatalogstandards/sist/c022fila0-64Id-4c3a-8295- 8961 f3de9e8/so-9692-12013 @ ISO 2013 All rights reserved
ISO 9692-1:2013(E) Foreword bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical mittees. Each member body interested in a subject for which a technical mittee has been established has the right to be represented on that mittee. International organizations governmental and non-governmental in liaison with ISo also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are different types of ISo documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives Part 2. .iso.org/directives Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.ISO shallnot be held responsible foridentifying anyor all such patent rights.Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received. .iso.org/patents Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The mitte responsible for this documentis TSO/TC 44 Welding and alled processes Submittee (standards.iteh.ai) SC 7 Representation and terms. ISO 9692-12013 This second edition of ISO 9692-1caricels anidireplacesISO 9692-1:2003) whieh has been technically revised. fo sad sassaud pao puo fupia a jeaua8 a rapun sred Smoo au go ssisuoo ze96 os1 10-17696-05/80691968 joint preparation: -Part 1: Manual metal arc welding gas-shielded metal arc welding gas welding TIG welding and beam welding of steels --Part 2: Submerged arc welding of steels -Part 3: Metal inert gas welding and tungsten inert gas welding of aluminium and its alloys -Part 4: Clad steels iv @ ISO 2013 All rights reserved
ISO 9692-1:2013(E) Introduction This part of ISO 9692 defines the parameters characterizing the joint preparation and the collection of frequently recurring values and shapes. The specifications given in this part of ISO 9692 have been piled on the basis of experience and contain dimensions for types of joint preparation that are generally found to lead to suitable welding conditions. However the extended field of application makes it necessary to give a range of dimensions. The dimension ranges specified represent design limits and are not tolerances for manufacturing purposes. Manufacturing limits depend for instance on welding process parent metal welding position and quality level. Because of the mon character of this part of ISO 9692 the examples given cannot be regarded as the only solution for the selection of a joint type. Specific fields of application and manufacturing requirements (e.g. pipeline construction) may be covered by selected ranges specified in other standards adapted from this basic part of ISO 9692. Requests for official interpretations of any aspect of this part of ISO 9692 should be directed to the Secretariat of ISO/TC 44/SC 7 via your national standards body. A plete listing of these bodies can be found at .iso.org. iTehSTANDARDPREVIEW (standards.iteh.ai) ISO.9692-12013 htps:/standards.ich.ai/cataogstandards/s/c022fila0-64 1d-4c3a-8295- 8961f63de9e8/so-9692-1-2013 @ ISO 2013 All rights reserved
ISO-9692-1-2013 焊接和相关工艺 接头准备类型 第一部分：手工电弧焊、气体保护焊条电弧焊、气体保护焊、钨极氩弧焊和钢的光束焊接.pdf
