交换机配置（华为2326）.doc

sys *进入全局配置模式* Enter system view return userview with CtrlZ. [Quidway]vlanbatch100200300 *创建vlan100200300* [Quidway]undo vlan 300 *删除vlan300* [Quidway]vlan 255 *创建vlan 255* [Quidway-vlan255]quit *退出vlan配置模式，进入全局配置模式* [Quidway]undo interface vlan 1 *删除vlan1接口* [Quidway]inter vlan 255 *进入vlan255接口*
[Quidway-Vlanif255]ip add 10.10.10.10 255.255.255.0 *设置vlan255接口IP为10.10.10.10，掩码为255.255.255.0* [Quidway-Vlanif255]quit *退出vlan接口模式，进入全局配置模式* [Quidway]ip route 0.0.0.0 0 10.10.10.1 *配置默认网关为10.10.10.1* [Quidway]vlan500 *创建vlan500* [Quidway-vlan500]quit *退出vlan配置模式，进入全局配置模式* [Quidway]interether0/0/5 *进入端口5* [Quidway-Ethernet0/0/5]portdefaultvlan500 *配置端口5加入vlan500* [Quidway-Ethernet0/0/5]inter ether0/0/10
*进入端口10* [Quidway-Ethernet0/0/10]undoport default vlan *删除端口的default模式* [Quidway-Ethernet0/0/10]port link trunk *配置端口模式为trunk* [Quidway-Ethernet0/0/10]port trunk allow vlan 600 700 800 *允许600700800这些vlan通过该端口* [Quidway-Ethernet0/0/10]quit *退出端口10，进入全局配置模式* [Quidway]vlan 600 *创建vlan600* [Quidway-vlan600]vlan700 *创建vlan700* [Quidway-vlan700]vlan800 *创建vlan800*
*注意：不创建这三个vlan，“允许600700800这些vlan通过端口10”这条命令 就没有意义* [Quidway-vlan800]interether0/0/20 *进入端口20* [Quidway-Ethernet0/0/20]undonegoauto *删除端口自适应模式* [Quidway-Ethernet0/0/20]speed10 *强制端口速率为10M* [Quidway-Ethernet0/0/20]duplexhalf *强制端口工作模式为半双工* [Quidway-Ethernet0/0/20]user-intervty04 *进入用户接口vty04* [Quidway-ui-vty0-4]authentication-modeaaa *设置认证模式为账号密码形式* [Quidway-ui-vty0-4]aaa *进入认证配置模式*
[Quidway-aaa]local-user dianxin pass simple 123 *创建账号dianxin，密码为明文123* [Quidway-aaa]local-user dianxinlevel15 *设置账号dianxin的等级为最高15* [Quidway-aaa]local-user dianxin service-type telnet *设置账号dianxin的服务类型为telnet* [Quidway-aaa]undo local-user dianxin [Quidway-aaa]return *回到用户模式* save *保存配置* The current configuration will be written to the device. The current configuration will be written to the device. Are you sure to continue?[Y/N]y