BS EN 10028-4-2017压力用途用钢板第4部分 镍合金低温用钢(英文版).pdf

10028,2017,BS,EN,用钢,国外标准
文档页数:16
文档大小:1.63MB
文档格式:pdf
文档分类:国外标准
上传会员:
上传日期:
最后更新:

BS EN 10028-4:2017 EUROPEANSTANDARD EN10028-4 NORMEEUROPEENNE EUROPAISCHENORM July 2017 ICS 77.140.30; 77.140.50 Supersedes EN 10028-4:2009 English Version Flatproductsmade of steelsforpressurepurposes-Part 4:Nickelalloysteelswithspecified lowtemperature properties Produits plats en aciers pour appareils a pression - Flacherzeugnisse aus Druckbehalterstahlen - Teil 4: Partie 4 : Aciers alies au nickel avec caracteristiques Nickellegierte kaltzahe Stahle specifiees a basse temperature This European Standard was approved by CEN on 7 May 2017. EuropeanStandard tstatusfaationlstaadwithoutanylteration-tdatelistandbiliographicalrre concerning such national standards may be obtained on appliation to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English French German). A version in any otherlanguage made by Centre has the same status as the official versions. translation underthe responsibility of a CEN memberinto its ow language and notified to the CEN-CENELEC Management CEN members are the national standards bodies of Austria Belgium Bulgaria Croatia Cyprus Czech Republi Denmark Estonia Finland Former ugoslav Republic of Macedonia France Gemany Greece Hungary leland Ireland Italy Latvia Lithuania Luxembourg Malta Netherlands Norway Poland Portugal Romania Serbia Slovakia Slovenia Spain Sweden Switzerland Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITE EUROPEEN DE NORMALISATION EUROPAISCHES KOMITEE FOR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17 B-100o Brussels worldwide for CEN national Members. @ 2017 CEN Allrights of esxploitation in any form and by any means reserved Ref. No. EN 10028-4:2017 E
BS EN 10028-4:2017 EN 10028-4:2017 (E) Contents Page European foreword 1 Scope. 4 2 Normative references... 4 3 Terms and definitions. 4 4 Tolerances on dimensions.... 4 5 Calculation of mass. 4 6 Classification and designation. 4 6.1 Classification. 4 6.2 4 7 Information to be suppliedby thepurchaser. 4 7.1 Mandatory information.. 4 7.2 Options. 5 7.3 Example for ordering. 5 8 Requirements.. 5 8.1 Steelmaking proces. 5 8.2 Delivery condition... 5 8.3 Chemical position 5 8.4 Mechanical properties.. 7 8.5 Surface condition. 11 8.6 Internal soundness. 11 9 Inspection. 11 9.1 Typesofinspection andinspectiondocuments. .11 9.2 Tests to be carried out. 11 9.3 Retests sorting and reprocessing. 11 10 Sampling- 11 11 Test methods 11 12 Marking.. 11 13 Handling.. 11 AnnexA(informative)Guidelinesfor heat treatment. 12 Annex B (informative) Changes to the previous version EN 10028-4:2009. .13 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of Directive2014/68/EU aimed to be covered. .14 2
EN 10028-4:2017 (E) BS EN 10028-4:2017 Europeanforeword for pressure purposes" the secretariat of which is held by DIN. This document (EN 10028-4:2017) has been prepared by Technical Commitee ECISs/TC 107 *Steels be withdrawn at the latest by January 2018. identical text or by endorsement at thelatest by January 2018 and conflicting national standards shall rights. patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent This document supersedes EN 10028-4:2009. European Free Trade Association and supports essential requirements of Directive 2014/68/EU. document. For relationship with Directive 2014/68/EU see informative Annex ZA which is an integral part of this A list of changes between this document and the previous version can be found in Annex B. According to the CEN-CENELEC Internal Regulations the national standards organizations of the following countries are bound to implement this European Standard: Austria Belgium Bulgaria France Germany Greece Hungary Iceland IrelandItaly LatviaLithuaniaLuxembourgMalta Netherlands Norway Poland Portugal Romania Serbia Slovakia Slovenia Spain Sweden Switzerland Turkey and the United Kingdom. 3
BS EN 10028-4:2017 EN 10028-4:2017 (E) 1Scope This European Standard specifies requirements for flat products for pressure equipment made of nickel alloy steels as specified in Table 1. The requirements and definitions of EN 10028-1:2017 also apply. NOTEOnce this European Standard is published in the EU official Journal (OjEU)under Directive 2014/68/EU presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied needs to be done. 2Normative references indispensable for its application.For dated references only the edition cited applies.For undated references the latest edition of the referenced document (including any amendments) applies. EN 10020:2000 Definition and classification of grades of steel EN 10028-1:2017 Flat products made of steels for pressure purposes -Part 1: General requirements EN 10204:2004 Metallic products - Types of inspection documents 3Terms and definitions For the purposes of this document the terms and definitions given in EN 10028-1:2017 apply. 4Tolerances on dimensions See EN 10028-1:2017. 5Calculation of mass See EN 10028-1:2017. 6Classificationand designation 6.1 Classification In accordance with EN 10020:2000 all steel grades covered by this document are alloy special steels. 6.2 Designation See EN 10028-1:2017. 7Information tobe suppliedby the purchaser 7.1Mandatoryinformation See EN 10028-1:2017. 4
BS EN 10028-4:2017 EN 10028-4:2017 (E) 7.2 0ptions A number of options are specified in this European Standard and listed below.Additionally the relevant options of EN10028-1:2017 apply.Ifthe purchaser doesnot indicate awish to implement any of these options at the time of enquiry and order the products shall be supplied in accordance with the basic specification (see EN 10028-1:2017). 1)delivery condition other than that specified in Table 3 (see 8.2.2); 2)delivery of products in the untreated condition (see 8.2.3); 3)specification of a minimum impact energy of 40 J (see 8.4 and Table 4); 4)mid-thickness test pieces for the impact test (see Clause 10): 5) verification of impact energy for longitudinal test pieces (see Clause 11). 7.3Examplefor ordering 10 plates with nominal dimensions thickness = 50 mm width = 2000 mm length =10 000mm made of a steel grade with the name 15NiMn6 and the number 1.6228 as specified in EN 10028-4 to be delivered with inspection certificate 3.1 as specified in EN 10204 10 plates -50 ×2000 ×10 000-EN10028-4-15NiMn6-Inspection certificate3.1 J0 10 plates - 50 × 2000 × 10 000 - EN 10028-4 - 1.6228 - Inspection certificate 3.1 8Requirements 8.1 Steelmaking process See EN 10028-1:2017. 8.2 Delivery condition 8.2.1The delivery condition shall be noted in the inspection document. 8.2.2 Unless otherwise agreed at the time of enquiry and order the products covered by this document shall be supplied in the usual delivery conditions specified in Table 3. 8.2.3 If so agreed at the time of enquiry and order the products may be supplied in the untreated condition. In these cases the specified tests shall be carried out on test pieces in the usual delivery condition as given in Table 3. Annex A contains heat treatment information for the purchaser. 8.3Chemicalposition o oso de o s analysis. 8.3.2The product analysis shall not deviate from the specified values for the cast analysis as specified in Table 1 by more than the values given in Table 2. 5

资源链接请先登录(扫码可直接登录、免注册)
①本文档内容版权归属内容提供方。如果您对本资料有版权申诉,请及时联系我方进行处理(联系方式详见页脚)。
②由于网络或浏览器兼容性等问题导致下载失败,请加客服微信处理(详见下载弹窗提示),感谢理解。
③本资料由其他用户上传,本站不保证质量、数量等令人满意,若存在资料虚假不完整,请及时联系客服投诉处理。

投稿会员:一修
我的头像向阳而生!

您必须才能评论!

手机扫码、免注册、直接登录

 注意:QQ登录支持手机端浏览器一键登录及扫码登录
微信仅支持手机扫码一键登录

账号密码登录(仅适用于原老用户)