ASMEBPVC.VII1.1-2023 SECTION Rules for Construction of Pressure Vessels ASME Boiler pue 2023 Pressure Vessel Code An InternationalCode Division 1 ASME SETTING TRE STANDARD
soeoss s or the ASME Single Certification Mark shall not be used on any item that is not constructed in accordance with all of the applicable requirements of the Code or Standard. Use of the ASME available such ASME markings may not be used. (For Certification and Accreditation Programs see Items produced by parties not formally possessing an ASME Certificate may not be described either explicitly or mplitly as ASME certified or approved in any code forms or other document.
AN INTERNATIONAL CODE 2023ASMEBoiler& PressureVesselCode 2023 Edition July 1 2023 VIlI RULESFORCONSTRUCTION OFPRESSUREVESSELS Division 1 on Pressure Vessels ASME Boiler andPressure Vessel Committee Mechanical Engineers TheAmericanSocietyof Two Park AvenueNew York NY10016 USA
Date of Issuance: July 1 2023 American National Standards and it is an American National Standard.The standards mitte that approved the code or standard was balanced to ensure that individuals from petent and concerned interests had an op- portunity to participate. The proposed code or standard was made available for public review and ment which provided an opportunity for additional public input from industry academia regulatory agencies and the public-at-large. ASME does not “approvecertify ” rate” r endorse” any item construction proprietary device or activity. ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document and does not undertake to insure anyone utilizing a standard against lia- bility for infringement of any applicable letters patent nor does ASME assume any such liability.Users of a code or o a peds e oa op pesdae pp gement of suchrights is entirely their own responsibility. epa qu snppe suad ssaduuleeapqe government or industry endorsement of this code or standard. ASME acceptsresponsibility fornly thoseinterpretationsof thisdocument issuedinaccordance withthes tablished ASME procedures and policies which precludes the issuance of interpretations by individuals. The endnotes and preamble in this document (if any) are part of this American National Standard. A ASME Collective Membership Mark V ASME Single Certification Mark ASME* and the above ASME symbols are registered trademarlks of The Amerian Society of Mechanical Engineers. No part of this document may be reproduced in any form in an electronic retrieval system or otherwise without the prior writen permission of the publisber. Library of Congress Catalog Card Number: 56-3934 Adopted by the Council of The American Society of Mechanical Engineers 1914; latest edition 2023. The American Society of Mechanical Engineers Two Park Avenue New Yorlk NY 10016-5990 Copyright @ 2023 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All rights reserved Printed in U.S.A.
TABLEOFCONTENTS List of Sections xxi Foreword xxxi Statement of Policy on the Use of the ASME Single Certification Mark and Code Authorization in Advertising xXx Statement of Policy on the Use of ASME Marking to Identify Manufactured Items xXX xxvi Correspondence With the Committee vi Summary of Changes lx Cross-Referencing in the ASME BPVC bxvi Introduction 1 U-1 Scope 1 U-2 General U-3 Standards Referenced by This Division 4 U-4 Units of Measurement .................. 5 U-5 Tolerances 5 Subsection A General Requirements 8 Part UG General Requirements for All Methods of Construction and All Materials 8 UG-1 Scope 8 Materials 8 UG-4 General 8 UG-5 Plate 9 UG-6 Forgings 6 UG-7 Castings 9 UG-8 e d 9 UG-9 Welding Materials 10 UG-10 Material Identified With or Produced to a Specification Not Per- mitted by This Division and Material Not Fully Identified 10 UG-11 Prefabricated or Preformed Pressure Parts . . 11 UG-12 Bolts and Studs 13 UG-13 ssea pue snn 13 UG-14 Rods and Bars 13 UG-15 Product Specification 14 Design 14 UG-16 General 14 UG-17 Methods of Fabrication in Combination 15 UG-18 Materials in Combination 15 UG-19 Special Constructions 15 UG-20 Design Temperature 16 UG-21 Design Pressure 17 UG-22 Loadings 17 UG-23 Maximum Allowable Stress Values 17 UG-24 Castings ......... 19 UG-25 Corrosion 19 UG-26 Linings 20 UG-27 Thickness of Shells Under Internal Pressure .................. 20 UG-28 Thickness of Shells and Tubes Under External Pressure ........ 20 UG-29 Stiffening Rings for Cylindrical Shells Under External Pressure 24 UG-30 Attachment of Stiffening Rings 26
ASME BPVC.VIII.1-2023压力容器建造规则(708页英文版).pdf
